Pitches
Step 1 — pick the pitch Tap a pitch to open the zonePitching: — · Tap a pitcher on the Dashboard to switch — their pitch list and counts follow them. Softball preset
Defensive Plays
Sends on its own, shows orange on the watchCustom Message
Typed text — watch buzzes twice, clears in 10 secWatch — what the watch should show
Mirror of the last call sent — not a live feedCalls show for the display time set on the Dashboard (10 seconds here) — the line at the top of the square face retreats as time runs out — then the watch falls back to WAIT FOR NEXT PLAY, where the battery readout lives. Battery stays off the call screen.
Watch banner (top of every call screen): ꓘONTROL
Offense — Pick a Player
Individual calls to individual players — only their watch buzzesWith the 9-watch Full Team Kit ($1,349), every player in the lineup wears a watch. Pick who gets the call first — the batter, a runner, a pair, or the whole team — then tap the play below. A steal goes to the runner only. A bunt goes to the batter only. Nobody else has to see it, and the other dugout never does.
Sending to: #8 Harper J. — Batter · Tap another player to change who gets the next call. Tap “All 9 — Whole Team” to send to every watch.
Offensive Calls
Fully customizable — edit, delete or add in Dashboard › Offense CallsBuilt in: Bunt, Sac Bunt, Drag Bunt, Hit & Run, Steal, Steal 2nd / 3rd / Home, Delayed Steal, Fake Bunt, Fake Bunt Steal, Squeeze, Safety Squeeze, Suicide Squeeze, Take, and Hit Away. Don’t run one? Delete it in the Dashboard. Call it something else? Rename it there — your playbook, your words.
Watch — what that player sees
Only the selected player’s watch shows thisExample: you pick Runner on 1st and tap STEAL 2ND — only that runner’s watch buzzes and shows STEAL 2ND. The batter’s watch stays on WAIT unless you send them a call too (like Fake Bunt Steal, which is built to go to both).
Offense count this game: 0 calls sent · All offensive sends are recorded in the Log tab under “Offense.”
Sport — Playbook Preset
One board, two presets — only the playbook swapsSwitching sport swaps pitches, defensive plays, offensive calls, and the sample roster. Edits you make in one sport are kept for that sport when you switch back during this visit. Reset in the Playbook Editor restores the selected sport’s starter set.
Pre-Game Check
Battery under 20% gets flagged before first pitch| ID | Label | Last ACK | Batt | Signal | Last call |
|---|
A watch with no ACK in the current call window shows as Not Confirmed — that is not the same as failed: an ACK can be lost even when the call arrived, because the watch's ACK link is weaker than the hub's call link.
Tournament Mode
Pitch counts reset for each new gameEdit Pitchers
Names, numbers & pitches for the pitcher picked abovePitches — who throws what
Tap a pitch to turn it on or off for that pitcher. Only their pitches show on the Calls tab when they are the pitcher picked above.
Name and number changes apply right away — the pitcher circles above, the Calls tab, and new log entries all use them. New pitchers start at zero and show up above immediately. Delete removes a pitcher for good — tap Delete, then tap again to confirm. In this demo, edits last for this visit only.
Playbook Editor
Rename calls — the grids update right awayPitches
Defensive Plays
Added pitches and plays appear on the Calls tab right away — rename them in the fields above. Delete removes one for good — tap Delete, then tap again to confirm. Deleting a pitch also takes it off every pitcher's list. Defensive plays only: each play has a Line 2 field — type a word there and it stacks under the play's name on the Calls tab and on the watch, so one call can show two lines, one over the other. Leave Line 2 blank for a one-line call.
Offense has its own editor below — Dashboard › Offense Calls — so you can edit, delete, and add offensive calls without digging through the pitch playbook.
Offense Calls
Edit · Delete · Add — the Offense tab updates right away 16 callsThis is your offensive playbook. Edit any name in its field, Delete a call you don’t run (tap Delete, then tap again to confirm), or Add a new one below. Changes show on the Offense tab and on the watch immediately.
Rename them to your team’s words — “Bunt” can be whatever you call it in the dugout. Add makes a new call at the end of the Offense grid; type a name above and tap Add to name it as you add it, or tap “+ Add Offense Call” for a blank one and rename it in the list. In this demo, edits last for this visit only.
Location Editor
Rename the zones & off-plate calls — Step 2 updates right awayZones — on the plate
Off the plate
Locations are listed in the same order as the zone grid — top row first, inside to outside. The name is what shows on the watch and in the log; the description is the small line under each off-plate button on the Calls tab. Add makes a new off-plate call — rename it and give it a description in the fields above. Delete removes one for good — tap Delete, then tap again to confirm.
Call Display Time
How long a call stays on the watch before it goes back to WAITApplies to every call — pitches, defense, combo, custom messages and tests. The watch counts down with its timer bar and clears to WAIT FOR NEXT PLAY when the time is up. Default is 10 seconds.
Firmware Update
Upload new firmware — hub and watch are separate filesIn the game-day version, these open the hub's update pages. In this demo they don't upload anything — they just show where the buttons live.
Watch Wi-Fi OTA
Update watches over the APUpload a watch firmware file to the hub first, then push it. Watches must be on, in range, and over 20% battery. A watch shows UPDATING, downloads, and reboots to WAIT. Do not send calls during the ~20 seconds an update takes.
Pitch Count
Counts calls SENT, regardless of ACKA pitch was called even if a watch ACK was lost, so the count follows what you sent, not what ACKed. Defensive plays and tests are never counted here. Combo calls count as a pitch.